Tips to be a Successful Septic Tank Owner
The average household septic tank system should be inspected at least every three years by a professional septic tank company. Residential septic tanks are typically pumped every three to five years.
Four major factors influence the frequency of septic tank pumping:
•Size of Household
•Total wastewater generated
•Volume of solids in wastewater
•Size of septic tank
What happens when a septic tank company is coming to inspect your septic tank:
When you call a Sandy Springs septic tank company, they will inspect for leaks and examine the scum and sludge layers in your septic tank.
It is important to keep maintenance records on the work performed on your septic tank system.
Your septic tank includes a T-shaped outlet which prevents sludge and scum from leaving the septic tank and traveling to the drainfield area. If the bottom of the scum layer is within six inches of the bottom of the outlet, or if the top of the sludge layer is within 12 inches of the outlet, your septic tank needs to be pumped.
To keep track of when to pump out your tank, keep a diary of the sludge and scum levels found by the septic professional.
The licensed plumbing company should note repairs completed and the septic tank condition in your system’s service report. If other repairs are recommended, hire a Sandy Springs professional septic tank company soon.
What Causes Septic Tanks to Back-Up?
Septic tanks are designed to hold human biological waste material right until bacteria break it down into gases, solids and water. The tank itself is usually made from concrete, but can also be built from non-degradable materials. It is very important to take proper care and maintain your septic system so that they work properly at all times.
Septic Systems And Their Problems
Some of the most common problems in septic systems are the following:
• Use Of Strong Chemicals: Toxic chemicals such as gasoline, motor oil, solvents, pesticides and other chemical products that are put into the drain harm the nearby soil, making it unfit for the growth of plants. They also destroy the bacteria needed to break down the waste in the tank.
• Flushing Down Non-Biodegradable Items: These items never break down naturally and only fill up space. It only ups the liquid levels in the tank and causes clogging.
• Too Much Water In The Tank: When there is too much water in the tank, the waste does not get a chance to break down, and this eventually blocks the distribution tubes.
• Use Of Too Much Detergent: Overuse of detergents cause a lot of problems with your pipes and tanks as the excess residue can stick to the sides and corrode the pipes.
These are just some of the common problems and preventive measures that you need to keep in mind when it comes to your septic tanks.
Septic Systems: Their Problems and Maintenance
What is a Sewage Pump?
A sewage pump is used to transfer sewage liquids and solids from one place to another. Usually, in residential applications, sewage includes soft solids up to 2" in diameter is pumped from a sewage basin to a sewer system or a septic tank. A sewage pump is installed at the lowest point of the sewage basin.
Since the pump is submerged most of the time, it is also referred to as a submersible sewage pump. Sewage pump can be automatic, manual or dual mode. A dual mode pump contains a piggyback plug, which allows the pump to be used as either manual, wherein the pump bypasses the switch and is plugged in directly into the socket or as automatic, wherein the pump is plugged in through the floating switch and works only when the switch is activated.
Due to a possibility of sewage overflow, it is generally not advised to use a manual sewage pump inside of a sewage basin.
Sewage pumps are centrifugal pumps, with special design enabling solids to pass without clogging the pump. When the pump is turned on, the motor starts to rotate the impeller, creating the pressure that pushes water into the impeller and goes into the discharge pipe.
The sewage pump is powered through a 10-25 ft. electric cord. Depending on the model, the voltage can be 115, 230, 460, or 575 volts. The pump housing, which contains a motor and an impeller, is made with cast iron and is built for long term use.
Types of Sewage Pumps
• Check for a small 3/16 to 3/8 inch weep hole in the discharge pipe directly above it.
• Visually inspect all alarm mechanisms (if applicable), exposed metal parts and connections for corrosion. You may apply a silicone water repellant spray to deter corrosion. Refer to manufacturer usage instructions to apply silicone spray.
• Verify that there is a check valve in place on the drain line just above the pump cover. Contact a licensed plumber in [post_name] to add a check valve if one is not present.
• Check to make sure the air gap in between the interior and exterior discharge pipes should be open and clear of debris.
There are many pumping station facilities, including pumps and equipment for pumping fluids from one place to another. They are used for a variety of infrastructure systems, such as supplying water to canals, and the removal of sewage to the processing site. This station in sewage collection system also called lift station, are designed to handle raw sewage that is fed from underground pipelines.
Businesses in [post_name] can benefit from using sewage pumps as it can handle loads of water in a small amount of time. It is cost efficient if you have a sewage pump to handle those unwanted water and wet waste.
Learn more about how sewage pumps work and how they can help your business.